11000 Pro Farmhttp://www.interstatepullers.com/11000-pro-farm/en-US2010-02-09T02:27:22ZSquarespace Site Server v5.9.1 (http://www.squarespace.com/)11000 LB. PRO FARM STOCKhttp://www.interstatepullers.com/11000-pro-farm/2009/1/28/11000-lb-pro-farm-stock.htmlInterstate Pullers2009-01-28T12:11:38Z

Competition vehicles must have standard block and crankcase for make and model being entered. Repower engines must use original equipment size and type injection pump for the tractor being entered, or injection pump must be maximum of one "A" line pump (German Bosh, one plunger per cylinder). No P-pumps. Tractor identification by transmission, rearend and chassis size, with stock appearance. Hood, side shields, etc may be updated to make of tractor. Tractors must have wide front axles. Front wheels must track within rear wheels. Must have steel flywheel and clutch components. No cast parts allowed in clutch system.

Engine cubic inch limit of 540 cid.

Vehicles must have OEM cylinder head and must be for series engine used - No recast; No aluminum; No overhead cams allowed.

Diesel tractors only.

Intercoolers and water injection allowed.

Turbo charger must be under hood. See drawing - Link Here - for maximum turbo charger size.Turbo charger must have a 2.4" maximum inlet bore at the compressor wheel or a restrictor plate 1/4" thick with a hole no larger than 2.4" in diameter within 2" of compressor wheel. There must be only one turbo going through one pressure stage.

Exhaust must discharge vertically upward above highest point of tractor, exception of roll bars, and be securely attached. Exhaust must be at least 18" above the hood and no curved pipes or rain caps allowed. Exhaust pipe must be cross-bolted with two 3/8" grade five bolts within 1" of each other in vertical pipe and two 5/16" bolts within one inch of exhaust housing..

Vehicle with a plastic or fiberglass hood must be shrouded in the turbo area with a minimum metal thickness of .060" or 1/16".

All engine fans must be shrouded with steel 1/16" or thicker 360 degrees or factory.

Minimum drawbar length 18" from center of rear wheels to point of hook. Draw-bar must be rigid in all directions. Maximum 20" from top of hitch to the ground. Drawbar must be parallel to the ground. Hitch must be horizontal - Not vertical. No cast iron drawbar components. Draw bar must be horizontally pined.

All tractors will require:

• Air shut off - must also be able to be operated manually (by the operator from the seat of the tractor).
• Flywheel protection in the form of either:
  • A scatter blanket with six straps.
  • 6" x 3/8" steel around the flywheel area.
• Rear wheelie bars installed in accordance with the following specifications:
  • Pads on bottom of bars to be a minimum of 5 in. sq. pads
  • Pads to be a minimum of 32" rearward from the center of the rearend housing.
  • Pads maximum of 10" off the ground.
  • Outside to outside width of pads to be a minimum of 20".
  • Minimum 12" high bumper bars - top to be fastened to stabilizer bar framing.
  • Bars must support weight of tractor for weight class being pulled.
• Dead man's throttle.
• Neutral light - Light must come on in neutral & start in neutral, with light on.
• Side shields are allowed and must be made out of .060" or 1/16" metal.
• Harmonic balancer to be shielded to be contained within vehicle.

Maximum tire width is to be 24.5" US. or 650 x 65 metric, maximum rim diameter of 38". No cut tires or puller 2000 H.P. No alterations to front edge of bar, tread, or cleat of tires.

Removal of PTO and hydraulics (rockshafts) allowed - if not removed PTO shafts must be covered with a safely shield.

The frame and weights must not extend any further than 12" from center of the rear axle to further most point - excluding tow hook. the wheelbase must not exceed 114"

Competing vehicles must have working rear wheel brakes.

Competing vehicles must have fenders that consist of a solid barrier between the driver nd any part of the rear tires. The barrier must  be able to sufficiently support the weight of the driver and must extend a minimum of 6" horizontally at the top, and be a minimum of 36" wide at the top.

Vehicle must have a rollover protection bar or cage that is at least as high as the top of the drivers head/helmet. Rollover protection must be fastened at least two poionts to the rear axle housing. Factory style flip down tops allowed. Rollover protection must be able to lift one rear wheel when pulled horizontally from the top of the bar/cage without damage to the rollbar/cage.

Top 3 finishing tractors are subject to inspection.

Driver must wear fire suit and helmet.

Fire extinguisher is required.

]]>